Home > ELECTRICAL > CURTIS > MODEL 1206 >

1206-4301 36V 350A Ezgo W/o Plug
1206-4301 Curtis E-Z-GO 36V 350A Controller
 
Our Price: $247.35

Price with Selected Options: $247.35




Check compatibility. Ask our experts.
Part Number:
1206-4301


Condition*:
Brand New ($518.95)
Remanufactured OEM ($247.35) -

Repair Service ($195.94) - Save $51.41

Qty:  
Description
 

1206-4301 Curtis E-Z-GO 36V 350A Controller without Plug

Category: Curtis Model 1206

Product Description

This is a Curtis 36 Volt and 350 Amp SX Controller for E-Z-Go TXT and Medalist Golf Carts with Parts Number: 1206-4301 or Curtis 1206-4301.


Cross Reference Numbers:

  • CL7007823
  • CT1206-4301
  • HU4067951
  • YP550067818
  • YP5500678-18
  • 7007823
  • 4067951
  • 550067818
  • 5500678-18

Suggested Accessories Parts Numbers:

76-1415-GOLF , 76-908HRNS48V , 76-908R3648BNJO , 94-CM174 , 100-586117111 , 24-CBHF2-EZ36 , 43-8012-30 , 76-1415-GOLF , 76-908HRNS48V , 76-908R3648BNJO , 94-CM174 , 100-586117111 , 24-CBHF2-EZ36 , 43-8012-30 , 76-1415-GOLF


Application: The Curtis 1206-4301 Controller works on E-Z-Go Medalist and TXT Carts with ITS Throttle, from 1994 to the present. This SX Motor Controller is not suitable for PDS or DCS Models.

Product Specifications

Specifications of the 1206-4301 E-Z-Go Controller:

Part Category Cart Motor Speed Controller
Brand Curtis
Drive System New Curtis Master Drive
Fitment Direct Replacement
Current 350A
Voltage 36V
Throttle Type ITS Throttle Input
Number of Pins 5
Number of Plug Bars 3
Weight 2 lbs.
Dimension 6.5" x 4.5" x 2.5"
Condition Rebuilt
Fitment Direct Replacement

Curtis 1206-4301 Controller

The 1206-4301 EZGO Controller is a remanufactured Motor Speed Controller for E-Z-Go TXT and Medalist Golf Carts. It is a 36V controller with ITS throttle. The 1206-4301 Controller is designed to replace the stock controllers on E-Z-Go 36V carts with ITS throttle only. It has an extra 50 Ampere than the stock controller which adds extra torque. It is responsible for regulating the speed level and performance of your vehicle while maintaining E-Z-Go safety standards.


An image of a 1206-4301 Controller


An image of a Curtis 1206-4301 E-Z-GO Controller (Top View 2)


An image of a 1206-4301 Curtis E-Z-GO Controller (Front View)


Figure: 1206MX-4301 E-Z-GO Controller1

Pre-installation Tests

Before installing the 1206-4301 Controller, you must conduct a set of tests defined in the instruction manual that comes with the controller. Upon installation, you may encounter problems that may be due to a faulty controller or a faulty cart. The following tests will help diagnose if the fault is a cart fault or controller fault.


CHECK MOTOR WINDINGS:

  1. Set your VOM to RESISTANCE (Ω).
  2. With your motor disconnected, measure A1 to A2. This must measure BETWEEN .3Ω and 1Ω.
  3. With your motor disconnected, measure F1 to F2. This must measure BETWEEN 1Ω and 2Ω.
  4. With your motor disconnected, measure A1 to F1. This must measure OPEN.
  5. With your motor disconnected, measure F1 to motor case. This must measure greater than 5MΩ.

CHECK MAIN SOLENOID:

  1. Disconnect all wires from the main solenoid.
  2. Set your VOM to RESISTANCE (Ω).
  3. Measure the solenoid coil. This must measure NO LESS than 100Ω.
  4. Connect VOM leads to the main solenoid lugs.
  5. Attach jumpers from the main battery positive and negative to the coil (small terminals).
  6. The meter must jump from infinity to LESS THAN .3Ω.
  7. Remove jumpers and reconnect solenoid wiring from the harness. (If suppression diode is present,
  8. The non-banded side must go the blue wire – pin J1-6 from the controller.)

CHECK COTHERM:

  1. Inspect the cotherm (insulating material) mounted to the heat sink for holes, debris, and tears.
  2. Repair or replace, if necessary.

CHECK THE CART WIRE HARNESS:

  • Check the connectors on the wire harness for corrosion, loose, broken, burnt or missing pins.
  • Repair or replace pins as necessary.

Warranty Information

The EZGO 1206-4301 Controller comes with a 6-months limited warranty, extendable up to 36 months.

Frequently Asked Questions

Is this Curtis 1206-4301 a new Controller?

No, the 1206-4301 EZGO Controller is a rebuilt item.

What is the current rating of the 1206-4301 Controller?

This Controller is rated at 350 Amps.

Does it work with PDS or DCS models?

This Controller does not work with PDS or DCS models. It only works with Medalist and TXT models (1994 to present).

Can it replace other 36V stock controllers with 300 Amps?

Yes, it can replace stock 300A controllers and thus provides extra torque.

Do I need to pay a core charge for the EZGO 1206-4301 Controller?

Yes, all remanufactured and rebuilt items are subject to a core charge. A core charge is refundable. The refund amount will be determined by the status of the core returned.

What kind of throttle does it use

The 1206-4301 uses ITS throttle.

How many Pins does it have?

It has 5 Pins in a 4+1 configuration.

Does it have 3 plug bars?

Yes, the 1206-4301 Controller does not have the 4th plug bar.

More Parts For EZGO Golf Cart

Beside Curtis 1206-4301 Controller, if you need More Electrical Parts for EZGO Golf Carts, we have a huge collection of



An image of A part of E-Z-GO Golf Cart Parts collection at Lift Parts Warehouse

Figure: A part of E-Z-GO Golf Cart Parts collection at Lift Parts Warehouse


Are you looking for something else? Please browse our Part Catalog here. Lift Parts Warehouse provides quality aftermarket parts at a very reasonable price. All parts come with a limited 1 Year Warranty. We also guarantee a 100% fit for our parts.


1The actual product may vary slightly in color and appearance. This image is for illustration purposes only.



Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 1 Write a review »

  0 of 0 people found the following review helpful:
 
5 of 5 Awesome January 12, 2018
Reviewer: James Kendrick  
No more no less..

Was this review helpful to you?